Modules
Area fill
The bot fills a rectangular area you define with a single block type on its own, bottom to top: pits, water, lava and plant-covered ground, with wait / stop / macro options when the block runs out.
Last updated: November 22, 2026
Area fill is the opposite of Area excavation: the bot completely fills a rectangular area (width × length × height) you define with the one block type you choose. Use it to close a pit, raise the ground, bury a water or lava lake or build a platform.
How is the area defined?
The area is defined like Area excavation: by a corner, a facing and three sizes. It starts at the corner and runs width blocks to the right of the facing and length blocks along it; the height goes up and includes the corner's own layer.
| Setting | Default | Description |
|---|---|---|
| Width (blocks) | 5 | 1-64. To the right of the facing. |
| Length (blocks) | 5 | 1-64. Along the facing. |
| Height (blocks) | 3 | 1-48. Upwards, including the corner's layer. When filling a pit it must cover the pit's depth (the bot's feet must be between the corner's y and the top layer of this height). |
| Use corner coordinates | No | When on, the area is filled from the X/Y/Z corner you entered, in the facing you chose. When off, the corner is the block the bot's feet are in and the bot fills the way it looks. |
| Facing | South | North, East, South or West. Only with the corner coordinates on. |
| Block to fill with | dirt | A single block name (lowercase, e.g. dirt, cobblestone). The bot places only this one; it must be in its inventory. |
How does it fill?
- Bottom to top, layer by layer. The bot does not move up before the bottom layer is finished; while filling a layer it stands one block above it, on top of the area.
- Pillaring or placing from the edge. On flat ground the bot jumps at the start of a layer and puts a block under its feet to rise, then walks only on the blocks it has put and fills the remaining cells; when the layer is done it jumps and places again to reach the next one. In a pit or in water the bot places from the rim (or from the blocks it has already put) onto the cells in its reach; middle cells it cannot reach from the rim are put once the cells around them are filled. When it finishes, the bot stays on top of or beside the area.
- Supported order. A cell is only filled when there is a solid block under or next to it; a cell without support is put off until its neighbours are filled. That is how deep pits and water surfaces get filled too.
- What gets filled? Air, water, lava, single-layer snow and plants (grass, flowers, saplings and the like) are filled; the bot breaks plants such as flowers and saplings first. Solid blocks (snow with two or more layers included) are left alone and skipped.
- If an entity is in a cell, the bot waits a little first; if it is still there, the cell is skipped.
- Pits and water. The pit's bottom layer is filled too. In a water-filled pit the bot does not enter the water; it places from the rim, and water cells are replaced directly with the block. When a pit is very deep the bot starts with the cells it can reach from the rim and the rest follow once the cells around them are filled.
- Ceiling. When there is no room for the bot above the top layer (two blocks of free space), it places onto the cells from the side; cells it cannot reach from anywhere are skipped and the reason is printed. So in areas filled up to a ceiling, edge cells may sometimes stay empty.
- A summary every time. When the fill ends, is stopped or is cut short by an error, the console prints the number of blocks placed and cells skipped with the reason. If the area is still not loaded the bot waits; you can end it with
.fill stop.
When materials run out
At the start the number of blocks needed is worked out and shown together with the ones in the inventory in the .fill status output. When the block runs out, the When materials run out setting applies.
| Option | What happens? |
|---|---|
| Wait (carries on once given materials) | The bot waits where it is and carries on when you put more blocks in its inventory (default). |
| Stop | The bot stops filling. Give it blocks and start again with .fill start. |
| Run a macro | The macro you chose runs (for example taking blocks from a chest) and the bot carries on where it left off. |
With a macro chosen, the After the macro setting decides how the bot goes back: *Walk back if close* walks it back when it is close, *Carry on only if the macro brings it back* does not move the bot.
Speed and placing method
| Mode | What it does |
|---|---|
| Safe | Slow head movement and longer gaps. For servers with strict anti-cheat. |
| Normal | Works at the bot's general head pace (Bot behavior card). |
| Fast | Quick head movement and the shortest gap. Anti-cheat may roll it back on some servers; if so, go back to Safe or Normal. |
The Placing method can be *Places like a player, looking at the block* (default) or *Places by packet without turning the head*. Head and walking settings come from the bot's Bot behavior card.
Starting
- 1In the bot's settings turn on Enable the area fill module, enter the area and the block, and save. Restart the bot.
- 2Put the block to fill with in the bot's inventory (enough to fill the area).
- 3Place the bot inside the area or at most 4 blocks away. On the Area fill card in the console enter the corner and the size; the boxes save as you type. Pick the facing from the cards under Other corners, then press Start or type the command.
.fill start
.fill start 100 64 -20
.fill start 100 64 -20 8 12 6 east
.fill start here 8 12 6
.fill pause
.fill resume
.fill stop
.fill status
.fill speed safe|normal|fast| Command | What it does |
|---|---|
.fill start | Starts with the saved settings (from where it stands when the corner is off). |
.fill start x y z | Starts from the corner you give. |
.fill start x y z width length height [facing] | Starts with corner, sizes and facing (north, south, east, west). |
.fill start here width length height | Starts from where the bot stands, with the sizes you give. |
.fill pause / resume | Pauses / resumes. |
.fill stop | Stops filling. |
.fill status | Prints progress, the number of blocks needed and in the inventory, and the speed. |
.fill speed safe|normal|fast | Changes the speed right now. |
